|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
K4S511632D CMOS SDRAM DDP 512Mbit SDRAM 8M x 16bit x 4 Banks Synchronous DRAM LVTTL Revision 0.0 July. 2002 This is to advise Samsung customers that in accordance with certain terms of an agreement, Samsung is prohibited from selling any DRAM products configured in "Multi-Die Plastic" format for use as components in general and scientific computers, such as mainframes, servers, work stations or desk top personal computers (hereinafter "Prohibited Computer Use"). Applications such as mobile, including cell phones, telecom, including televisions and display monitors, or non-desktop computer systems, including laptops, notebook computers, are , however, permissible. "Multi-Die Plastic" is defined as two or more Dram die encapsulated within a single plastic leaded package * Samsung Electronics reserves the right to change products or specification without notice. Rev. 0.0 July. 2002 K4S511632D CMOS SDRAM Revision 0.0 (July, 2002) Rev. 0.0 July. 2002 K4S511632D 8M x 16Bit x 4 Banks Synchronous DRAM FEATURES * JEDEC standard 3.3V power supply * LVTTL compatible with multiplexed address * Four banks operation * MRS cycle with address key programs -. CAS latency (2 & 3) -. Burst length (1, 2, 4, 8 & Full page) -. Burst type (Sequential & Interleave) * All inputs are sampled at the positive going edge of the system clock. * Burst read single-bit write operation * DQM for masking * Auto & self refresh * 64ms refresh period (8K Cycle) Part No. K4S511632D-KC/L7C K4S511632D-KC/L75 K4S511632D-KC/L1H K4S511632D-KC/L1L CMOS SDRAM GENERAL DESCRIPTION The K4S511632D is 536,870,912 bits synchronous high data rate Dynamic RAM organized as 4 x 8,392,608words by 16bits, fabricated with SAMSUNG's high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth, high performance memory system applications. ORDERING INFORMATION Max Freq. 133MHz(CL=2) 133MHz(CL=3) 100MHz(CL=2) 100MHz(CL=3) LVTTL 54pin TSOP(II) Interface Package FUNCTIONAL BLOCK DIAGRAM I/O Control LWE Data Input Register LDQM Bank Select 2 x 4M x 16 2 x 4M x 16 2 x 4M x 16 2 x 4M x 16 Refresh Counter Output Buffer Row Decoder Sense AMP Row Buffer DQi A ddress Register CLK ADD Column Decoder Col. Buffer LRAS LCBR Latency & Burst Length LCKE LRAS LCBR LWE LCAS Programming Register LWCBR LDQM Timing Register CLK CKE CS RAS CAS WE DQM * Samsung Electronics reserves the right to change products or specification without notice. Rev. 0.0 July. 2002 K4S511632D PIN CONFIGURATION (Top view) VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 V SS DQ15 V SSQ DQ14 DQ13 V DDQ DQ12 DQ11 V SSQ DQ10 DQ9 V DDQ DQ8 V SS N.C/RFU UDQM CLK CKE A12 A11 A9 A8 A7 A6 A5 A4 V SS CMOS SDRAM 54Pin TSOP (II) (400mil x 875mil) (0.8 mm Pin pitch) PIN FUNCTION DESCRIPTION Pin CLK CS Name System cock Chip select Input Function Active on the positive going edge to sample all inputs. Disables or enables device operation by masking or enabling all inputs except CLK, CKE and DQM Masks system clock to freeze operation from the next clock cycle. CKE should be enabled at least one cycle prior to new command. Disable input buffers for power down in standby. Row/column addresses are multiplexed on the same pins. Row address : RA0 ~ RA12, Column address : CA 0 ~ CA 9 Selects bank to be activated during row address latch time. Selects bank for read/write during column address latch time. Latches row addresses on the positive going edge of the CLK with RAS low. Enables row access & precharge. Latches column addresses on the positive going edge of the CLK with CAS low. Enables column access. Enables write operation and row precharge. Latches data in starting from CAS, WE active. Makes data output Hi-Z, tSHZ after the clock and masks the output. Blocks data input when L(U)DQM active. Data inputs/outputs are multiplexed on the same pins. Power and ground for the input buffers and the core logic. Isolated power supply and ground for the output buffers to provide improved noise immunity. This pin is recommended to be left No Connection on the device. CKE Clock enable A0 ~ A 12 BA 0 ~ BA1 RAS CAS WE L(U)DQM D Q0 ~ 15 Address Bank select address Row address strobe Column address strobe Write enable Data input/output mask Data input/output Power supply/ground Data output power/ground No connection /reserved for future use VDD /VSS VDDQ /VSSQ N.C/RFU Rev. 0.0 July. 2002 K4S511632D ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Voltage on VDD supply relative to Vss Storage temperature Power dissipation Short circuit current Symbol VIN, VOUT VDD, VDDQ TSTG PD IOS Value -1.0 ~ 4.6 -1.0 ~ 4.6 -55 ~ +150 2 50 CMOS SDRAM Unit V V C W mA Note : Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. DC OPERATING CONDITIONS Recommended operating conditions (Voltage referenced to VSS = 0V, TA = 0 to 70C) Parameter Supply voltage Input logic high voltage Input logic low voltage Output logic high voltage Output logic low voltage Input leakage current Symbol VDD, VDDQ VIH V IL VOH V OL ILI Min 3.0 2.0 -0.3 2.4 -10 Typ 3.3 3.0 0 Max 3.6 VDD +0.3 0.8 0.4 10 Unit V V V V V uA 1 2 IOH = -2mA IOL = 2mA 3 Note Notes : 1. VIH (max) = 5.6V AC. The overshoot voltage duration is 3ns. 2. VIL (min) = -2.0V AC. The undershoot voltage duration is 3ns. 3. Any input 0V VIN VDDQ . Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs. CAPACITANCE Clock RAS, CAS , WE, DQM Address, CS,CKE D Q0 ~ DQ8 (VDD = 3.3V, TA = 23C, f = 1MHz, VREF =1.4V 200 mV) Pin Symbol CCLK CIN CADD COUT Min 5.0 5.0 5.0 4.0 Max 9.0 10.0 10.0 6.5 Unit pF pF pF pF Note Rev. 0.0 July. 2002 K4S511632D DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, TA = 0 to 70C) Parameter Symbol Test Condition -7C Operating current (One bank active) Precharge standby current in power-down mode ICC1 Burst length = 1 tR C tRC(min) IO = 0 mA CKE V IL(max), tCC = 10ns CKE & CLK V IL(max), tCC = CKE V I H(min), CS VIH(min), tCC = 10ns Input signals are changed one time during 20ns CKE V I H(min), CLK VIL(max), tCC = Input signals are stable CKE V IL(max), tCC = 10ns CKE & CLK V IL(max), tCC = CKE V I H(min), CS VIH(min), tCC = 10ns Input signals are changed one time during 20ns CKE V I H(min), CLK VIL(max), tCC = Input signals are stable IO = 0 mA Page burst 4banks activated. tCCD = 2CLKs tR C tRC(min) CKE 0.2V C L 200 CMOS SDRAM Version -75 180 -1H 180 -1L 180 Unit Note mA 1 ICC2P ICC2PS ICC2N 4 4 40 mA Precharge standby current in non power-down mode ICC2NS Active Standby current in power-down mode ICC3P ICC3PS ICC3N mA 20 12 12 60 mA mA Active standby current in non power-down mode (One bank active) ICC3NS 50 mA Operating current (Burst mode) ICC4 220 220 240 240 mA 1 Refresh current Self refresh current ICC5 ICC6 440 400 6 3 380 380 mA mA mA 2 3 4 Notes : 1. Measured with outputs open. 2. Refresh period is 64ms. 3. K4S511632D-KC** 4. K4S511632D-KL** 5. Unless otherwise noticed, input swing level is CMOS(V IH/VIL=V DDQ/V SSQ). Rev. 0.0 July. 2002 K4S511632D AC OPERATING TEST CONDITIONS (V DD = 3.3V 0.3V, TA = 0 to 70C) Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition Value 2.4/0.4 1.4 tr/tf = 1/1 1.4 See Fig. 2 CMOS SDRAM Unit V V ns V 3.3V Vtt = 1.4V 1200 Output 870 50pF VOH (DC) = 2.4V, IOH = -2mA VOL (DC) = 0.4V, IOL = 2mA Output Z0 = 50 50 50pF (Fig. 1) DC output load circuit (Fig. 2) AC output load circuit OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) Parameter Row active to row active delay RAS to CAS delay Row precharge time Row active time Symbol -7C tRRD (min) tRCD (min) tRP(min) tRAS(min) tRAS(max) Row cycle time Last data in to row precharge Last data in to Active delay Last data in to new col. address delay Last data in to burst stop Col. address to col. address delay Number of valid output data tRC (min) tRDL(min) tDAL(min) tCDL(min) tBDL(min) tCCD (min) CAS latency=3 CAS latency=2 60 65 2 2 CLK + tRP 1 1 1 2 1 15 15 15 45 -75 15 20 20 45 100 70 70 Version -1H 20 20 20 50 -1L 20 20 20 50 ns ns ns ns us ns CLK CLK CLK CLK ea 1 2, 5 5 2 2 3 4 1 1 1 1 Unit Note Notes : 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and then rounding off to the next higher integer. 2. Minimum delay is required to complete write. 3. All parts allow every cycle column address change. 4. In case of row precharge interrupt, auto precharge and read burst stop. Rev. 0.0 July. 2002 K4S511632D AC CHARACTERISTICS Parameter CAS latency=3 CAS latency=2 CLK to valid output delay Output data hold time CAS latency=3 CAS latency=2 CAS latency=3 CAS latency=2 tCH tCL tSS tSH tSLZ tSHZ tOH 3 3 2.5 2.5 1.5 0.8 1 5.4 5.4 tSAC (AC operating conditions unless otherwise noted) Symbol Min CLK cycle time tCC 7.5 7.5 5.4 5.4 3 3 2.5 2.5 1.5 0.8 1 5.4 6 -7C Max 1000 Min 7.5 10 5.4 6 3 3 3 3 2 1 1 6 6 -75 Max 1000 Min 10 10 6 6 3 3 3 3 2 1 1 -1H Max 1000 CMOS SDRAM -1L Min 10 12 6 7 ns ns ns ns ns ns 6 7 ns 2 3 3 3 3 2 ns 1,2 Max 1000 ns 1 Unit Note CLK high pulse width CLK low pulse width Input setup time Input hold time CLK to output in Low-Z CLK to output in Hi-Z CAS latency=3 CAS latency=2 Notes : 1. Parameters depend on programmed CAS latency. 2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter. 3. Assumed input rise and fall time (tr & tf) = 1ns. If tr & tf is longer than 1ns, transient time compensation should be considered, i.e., [(tr + tf)/2-1]ns should be added to the parameter. DQ BUFFER OUTPUT DRIVE CHARACTERISTICS Parameter Output rise time Symbol trh Condition Measure in linear region : 1.2V ~1.8V Measure in linear region : 1.2V ~1.8V Measure in linear region : 1.2V ~1.8V Measure in linear region : 1.2V ~1.8V Min 1.37 Typ Max 4.37 Unit Volts/ns Notes 3 Output fall time tfh 1.30 3.8 Volts/ns 3 Output rise time trh 2.8 3.9 5.6 Volts/ns 1,2 Output fall time tfh 2.0 2.9 5.0 Volts/ns 1,2 Notes : 1. Rise time specification based on 0pF + 50 Ohms to VSS, use these values to design to. 2. Fall time specification based on 0pF + 50 Ohms to VDD, use these values to design to. 3. Measured into 50pF only, use these values to characterize to. 4. All measurements done with respect to VSS. Rev. 0.0 July. 2002 K4S511632D SIMPLIFIED TRUTH TABLE Command Register Mode register set Auto refresh Refresh Entry Self refresh Exit L H H CKEn-1 CKEn CS RAS CAS WE DQM BA0,1 CMOS SDRAM A11,A12, A9 ~ A 0 A10/AP Note H H X H L H X X L L L H L L H X L H L L H X H L L H H X H H X X OP code X 1,2 3 3 X X X V V X Row address L H Column address (A0 ~ A9 ) Column address (A0 ~ A9 ) 3 3 Bank active & row addr. Read & column address Write & column address Burst Stop Precharge Bank selection All banks Clock suspend or active power down Entry Exit Entry Precharge power down mode Exit DQM No operation command Auto precharge disable Auto precharge enable Auto precharge disable Auto precharge enable L L 4 4,5 4 4,5 6 H H H X X X L L L H L H H L X V X X H X V X L H H X V X X H X V L L L X V X X H X V X X X V L H X V X L H X H L H L H L X X X X X X V X X 7 X H L L H H H H L X H L X H X H X H X (V=Valid, X=Don't care, H=Logic high, L=Logic low) Notes : 1. OP Code : Operand code A0 ~ A12 & BA0 ~ BA 1 : Program keys. (@ MRS) 2. MRS can be issued only at all banks precharge state. A new command can be issued after 2 CLK cycles of MRS. 3. Auto refresh functions are as same as CBR refresh of DRAM. The automatical precharge without row precharge command is meant by "Auto". Auto/self refresh can be issued only at all banks precharge state. 4. BA0 ~ BA1 : Bank select addresses. If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected. If BA0 is "High" and BA 1 is "Low" at read, write, row active and precharge, bank B is selected. If BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank C is selected. If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected. If A10/AP is "High" at row precharge, BA0 and BA1 is ignored and all banks are selected. 5. During burst read or write with auto precharge, new read/write command can not be issued. Another bank read/write command can be issued after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst. 6. Burst stop command is valid at every burst length. 7. DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (Write DQM latency is 0), but makes Hi-Z state the data-out of 2 CLK cycles after. (Read DQM latency is 2) Rev. 0.0 July. 2002 |
Price & Availability of K4S511632D |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |